Indice del forum www.zeroshell.net
Distribuzione Linux ZeroShell
 
 FAQFAQ   CercaCerca  GruppiGruppi   RegistratiRegistrati 
 ProfiloProfilo  Log inLog in   Messaggi privatiMessaggi privati 

Problema con Acer Extensa E210 - ZS 1b10

 
Nuovo argomento   Rispondi    Indice del forum -> ZeroShell
Precedente :: Successivo  
Autore Messaggio
EtH



Registrato: 12/01/07 18:20
Messaggi: 18

MessaggioInviato: Mar Lug 01, 2008 3:34 pm    Oggetto: Problema con Acer Extensa E210 - ZS 1b10 Rispondi citando

Ciao Fulvio,
ho acquistato un paio di queste macchine per pochi euro con Linux "Memphis" preinsallato. Ovviamente la mia intenzione č di usarli con ZS aggiungendo una paio di sch. di rete con chip realtek ma ci sono un paio di problemi:
1) Il Boot da CD (SATA) nn ne vuole sapere -- Kernel Panic alla fine della ricerca della periferica USB/SATA

Avevo provato in precedenza con un cdrom IDE ma ZS 1b9 non veneva nč il disco nč la sch. di rete onboard. Ti allego un lspci (ho installato una debian etch per fare altre cose)

Ciao e Grazie

-[0000:00]-+-00.0 ATI Technologies Inc Unknown device 7910
+-01.0-[0000:01]----05.0 ATI Technologies Inc Unknown device 791e
+-07.0-[0000:02]----00.0 Marvell Technology Group Ltd. Unknown device 4364
+-12.0 ATI Technologies Inc SB600 Non-Raid-5 SATA
+-13.0 ATI Technologies Inc SB600 USB (OHCI0)
+-13.1 ATI Technologies Inc SB600 USB (OHCI1)
+-13.2 ATI Technologies Inc SB600 USB (OHCI2)
+-13.3 ATI Technologies Inc SB600 USB (OHCI3)
+-13.4 ATI Technologies Inc SB600 USB (OHCI4)
+-13.5 ATI Technologies Inc SB600 USB Controller (EHCI)
+-14.0 ATI Technologies Inc SB600 SMBus
+-14.1 ATI Technologies Inc SB600 IDE
+-14.3 ATI Technologies Inc SB600 PCI to LPC Bridge
+-14.4-[0000:03]----00.0 Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet
+-18.0 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
+-18.1 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
+-18.2 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
\-18.3 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Top
Profilo Invia messaggio privato MSN
JML.it



Registrato: 08/11/06 22:00
Messaggi: 26
Residenza: Castiglione del Lago (PG)

MessaggioInviato: Sab Lug 12, 2008 7:15 am    Oggetto: Rispondi citando

Confermo che su Acer con Lettori/Masterizzatori SATA il boot non funziona (nel mio caso, Acer Veriton M410).

Qualche informazione hardware della macchina utilizzata:

Codice:

root@zeroshell root> dmesg
sing MMCONFIG for extended config space
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:12.0: set SATA to AHCI mode
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
system 00:01: ioport range 0x4100-0x411f has been reserved
system 00:01: ioport range 0x228-0x22f has been reserved
system 00:01: ioport range 0x40b-0x40b has been reserved
system 00:01: ioport range 0x4d6-0x4d6 has been reserved
system 00:01: ioport range 0xc00-0xc01 has been reserved
system 00:01: ioport range 0xc14-0xc14 has been reserved
system 00:01: ioport range 0xc50-0xc52 has been reserved
system 00:01: ioport range 0xc6c-0xc6d has been reserved
system 00:01: ioport range 0xc6f-0xc6f has been reserved
system 00:01: ioport range 0xcd0-0xcd1 has been reserved
system 00:01: ioport range 0xcd2-0xcd3 has been reserved
system 00:01: ioport range 0xcd4-0xcdf has been reserved
system 00:01: ioport range 0x4000-0x40fe has been reserved
system 00:01: ioport range 0x4210-0x4217 has been reserved
system 00:01: ioport range 0xb00-0xb0f has been reserved
system 00:01: ioport range 0xb10-0xb1f has been reserved
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: ioport range 0x200-0x205 has been reserved
system 00:07: ioport range 0x290-0x297 has been reserved
system 00:0e: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:0f: iomem range 0xf0000-0xfffff could not be reserved
system 00:0f: iomem range 0xfed00000-0xfed000ff could not be reserved
system 00:0f: iomem range 0x2ffe0000-0x2fffffff could not be reserved
system 00:0f: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:0f: iomem range 0x0-0x9ffff could not be reserved
system 00:0f: iomem range 0x100000-0x2ffdffff could not be reserved
system 00:0f: iomem range 0x30000000-0x3fffffff has been reserved
system 00:0f: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0f: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0f: iomem range 0xfff80000-0xfffeffff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: d000-dfff
  MEM window: 0xfde00000-0xfdffffff
  PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
PCI: Bridge: 0000:00:07.0
  IO window: e000-efff
  MEM window: 0xfdd00000-0xfddfffff
  PREFETCH window: 0x00000000fdc00000-0x00000000fdcfffff
PCI: Bridge: 0000:00:14.4
  IO window: c000-cfff
  MEM window: 0xfdb00000-0xfdbfffff
  PREFETCH window: 0x00000000fda00000-0x00000000fdafffff
PCI: Setting latency timer of device 0000:00:07.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1580k freed
io scheduler noop registered
io scheduler anticipatory registered (default)
pci 0000:01:05.0: Boot video device
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
Allocate Port Service[0000:00:07.0:pcie03]
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
FDC 0 is a post-1991 82077
brd: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SB600_PATA: IDE controller (0x1002:0x438c rev 0x00) at  PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
SB600_PATA: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf900-0xf907, BIOS settings: hda:DMA, hdb:PIO
Probing IDE interface ide0...
hda: DVD-ROM BDV316G, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 40X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
Driver 'sd' needs updating - please use bus_type methods
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
EDAC MC: Ver: 2.1.0 Jun 26 2008
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input0
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ISO 9660 Extensions: RRIP_1991A
loop: module loaded
VFS: Mounted root (ext2 filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 300k freed
ISO 9660 Extensions: RRIP_1991A
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:02:00.0 to 64
sky2 0000:02:00.0: v1.21 addr 0xfddfc000 irq 19 Yukon-EC Ultra (0xb4) rev 3
sky2 eth0: addr 00:1c:25:3e:3c:22
No dock devices found.
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25.9 ehci_hcd
usb usb1: SerialNumber: 0000:00:13.5
hub 1-0:1.0: unable to enumerate USB device on port 5
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25.9 ohci_hcd
usb usb2: SerialNumber: 0000:00:13.0
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.25.9 ohci_hcd
usb usb3: SerialNumber: 0000:00:13.1
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.25.9 ohci_hcd
usb usb4: SerialNumber: 0000:00:13.2
ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 1-0:1.0: unable to enumerate USB device on port 5
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.25.9 ohci_hcd
usb usb5: SerialNumber: 0000:00:13.3
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.25.9 ohci_hcd
usb usb6: SerialNumber: 0000:00:13.4
usb 4-1: new full speed USB device using ohci_hcd and address 2
ahci 0000:00:12.0: version 3.0
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: controller can't do PMP, turning off CAP_PMP
usb 4-1: configuration #1 chosen from 1 choice
usb 4-1: New USB device found, idVendor=058f, idProduct=9360
usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-1: Product: USB Reader
usb 4-1: Manufacturer: 
usb 4-1: SerialNumber: 2004888
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver ub
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq sntf ilck led clo pio
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: Hitachi HDS721616PLA380, P22OAB3A, max UDMA/133
ata1.00: 321672960 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI: HL-DT-ST DVDRAM_GSA-H60N, CA01, max UDMA/100
ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
ata2.00: configured for UDMA/100
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 1:0:0:0: Direct-Access     ATA      Hitachi HDS72161 P22O PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
scsi 2:0:0:0: CD-ROM            HL-DT-ST DVDRAM_GSA-H60N  CA01 PQ: 0 ANSI: 5
scsi 2:0:0:0: Attached scsi generic sg1 type 5
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
sr 2:0:0:0: Attached scsi CD-ROM sr0
scsi 0:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
sd 0:0:0:0: [sdb] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg2 type 0
scsi 0:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
sd 0:0:0:1: [sdc] Attached SCSI removable disk
sd 0:0:0:1: Attached scsi generic sg3 type 0
scsi 0:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
sd 0:0:0:2: [sdd] Attached SCSI removable disk
sd 0:0:0:2: Attached scsi generic sg4 type 0
scsi 0:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
sd 0:0:0:3: [sde] Attached SCSI removable disk
sd 0:0:0:3: Attached scsi generic sg5 type 0
usb-storage: device scan complete
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda2.
NTFS driver 2.1.29 [Flags: R/W MODULE].
NTFS volume version 3.1.
warning: `named' uses 32-bit capabilities (legacy support in use)
nf_conntrack version 0.5.0 (12288 buckets, 49152 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
Bridge firewalling registered
DEFAULTBR: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
wlan: svn r3367
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
ath_rate_sample: 1.2 (svn r3367)
ath_pci: svn r3367
ath_pci: driver unloaded
ath_rate_sample: unloaded
ath_hal: driver unloaded
wlan: driver unloaded
sky2 ETH00: enabling interface
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
sky2 ETH00: Link is up at 100 Mbps, full duplex, flow control both
root@zeroshell root>


Codice:
root@zeroshell root> lspci
00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3)
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2)
00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS690 [Radeon X1200 Series]
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev 20)


Codice:
root@zeroshell root> lsusb
Unknown line at line 1809
Duplicate HUT Usage Spec at line 2650


Era collegato un lettore DVD IDE (per il boot), 1 masterizzatore Sata e un HD con delle partizioni.
Top
Profilo Invia messaggio privato
Mostra prima i messaggi di:   
Nuovo argomento   Rispondi    Indice del forum -> ZeroShell Tutti i fusi orari sono GMT + 1 ora
Pagina 1 di 1

 
Vai a:  
Non puoi inserire nuovi argomenti
Non puoi rispondere a nessun argomento
Non puoi modificare i tuoi messaggi
Non puoi cancellare i tuoi messaggi
Non puoi votare nei sondaggi


Powered by phpBB © 2001, 2005 phpBB Group
phpbb.it