Indice del forum www.zeroshell.net
Distribuzione Linux ZeroShell
 
 FAQFAQ   CercaCerca  GruppiGruppi   RegistratiRegistrati 
 ProfiloProfilo  Log inLog in   Messaggi privatiMessaggi privati 

bonding mode

 
Nuovo argomento   Rispondi    Indice del forum -> Reti
Precedente :: Successivo  
Autore Messaggio
renato.morano



Registrato: 23/09/10 09:37
Messaggi: 143

MessaggioInviato: Gio Giu 28, 2012 5:54 am    Oggetto: bonding mode Rispondi citando

Ciao,
uun po di teoria ....
mode=0 (balance-rr)
Round-robin policy: Transmit packets in sequential order from the first available slave through the last. This mode provides load balancing and fault tolerance.

mode=1 (active-backup)
Active-backup policy: Only one slave in the bond is active. A different slave becomes active if, and only if, the active slave fails. The bond's MAC address is externally visible on only one port (network adapter) to avoid confusing the switch. This mode provides fault tolerance. The primary option affects the behavior of this mode.

mode=2 (balance-xor)
XOR policy: Transmit based on [(source MAC address XOR'd with destination MAC address) modulo slave count]. This selects the same slave for each destination MAC address. This mode provides load balancing and fault tolerance.

mode=3 (broadcast)
Broadcast policy: transmits everything on all slave interfaces. This mode provides fault tolerance.

mode=4 (802.3ad)
IEEE 802.3ad Dynamic link aggregation. Creates aggregation groups that share the same speed and duplex settings. Utilizes all slaves in the active aggregator according to the 802.3ad specification.

Pre-requisites:
1. Ethtool support in the base drivers for retrieving
the speed and duplex of each slave.
2. A switch that supports IEEE 802.3ad Dynamic link
aggregation.
Most switches will require some type of configuration
to enable 802.3ad mode.

mode=5 (balance-tlb)
Adaptive transmit load balancing: channel bonding that does not require any special switch support. The outgoing traffic is distributed according to the current load (computed relative to the speed) on each slave. Incoming traffic is received by the current slave. If the receiving slave fails, another slave takes over the MAC address of the failed receiving slave.

Prerequisite:
Ethtool support in the base drivers for retrieving the
speed of each slave.

mode=6 (balance-alb)
Adaptive load balancing: includes balance-tlb plus receive load balancing (rlb) for IPV4 traffic, and does not require any special switch support. The receive load balancing is achieved by ARP negotiation. The bonding driver intercepts the ARP Replies sent by the local system on their way out and overwrites the source hardware address with the unique hardware address of one of the slaves in the bond such that different peers use different hardware addresses for the server.

The most used are the first four mode types...

Al momento le configurazioni possibili sono mode=0 (balance-rr) e mode=1 (active-backup).

In alcune configurazioni potrebbe servire usare altri modi .... qunidi aggiunguimoli:

Per esempio se volessimo aggiungere anche modo 5,6 modifichiamo il file
/root/kerbynet.cgi/template/bondconfig

aggiungendo le righe:

<input type=radio name=Type value=5 <xvar ATLBCHECKED>
onclick="typechanged()">&nbsp;&nbsp;Adaptive transmit load
balancing<br>
<input type=radio name=Type value=6 <xvar ALBCHECKED>
onclick="typechanged()">&nbsp;&nbsp;Adaptive load balancing<br>


Per avere la modifica anche al rebbot nel provilo attivo creare la dir bond e ci copiamo il file appena modificato
poi attraverso il tab Pre Boot script
si aggiunge la seguente procedura

cat /Database/bond/bondconfig >/root/kerbynet.cgi/template/bondconfig

.
A questo punto la modifica č attiva.
Top
Profilo Invia messaggio privato
Mostra prima i messaggi di:   
Nuovo argomento   Rispondi    Indice del forum -> Reti Tutti i fusi orari sono GMT + 1 ora
Pagina 1 di 1

 
Vai a:  
Non puoi inserire nuovi argomenti
Non puoi rispondere a nessun argomento
Non puoi modificare i tuoi messaggi
Non puoi cancellare i tuoi messaggi
Non puoi votare nei sondaggi


Powered by phpBB © 2001, 2005 phpBB Group
phpbb.it